User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Daytronic 10A72-2:Strain Gage Card
DATE:                  28-May-97
AUTHOR:                User Contributed
REVISION:              0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       5
NUMBER OF LINES:       100
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-                                                     F
  1.002  ASK+                                          X
  1.003  HEAD         ÍÍ INITIAL CONDITIONS ÍÍ
  1.004  DISP         The following Standard test equipment is required:
  1.004  DISP         1. Measurements Group 1550A Strain Indicator Calibrator
  1.004  DISP         ÿ  DTB # 55-2
  1.004  DISP         2. Strain Indicator Calibration Cable
  1.005  DISP         Connect the Daytronic Mainframe to the system Com1.
  1.006  DISP         With the Daytronic Model 10K6 mainframe turned off,
  1.006  DISP         remove any conditioner card that may be located in
  1.006  DISP         slot #1.
  1.007  DISP         Install the UUT into slot #1.
  1.008  DISP         Connect a Daytronic CONDITIONER CONNECTER model 60322,
  1.008  DISP         wired for two channels, to the rear of the UUT.
  1.009  DISP         Power up the Model 10K6 mainframe.
  1.010  HEAD         {}
  1.011  JMP          1.018
  1.012  HEAD         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
  1.013  HEAD         {º EXCITATION VOLTAGE TEST º}
  1.014  HEAD         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
  1.015  HEAD         {}ÍÍ EXCITATION VOLTAGE TEST ÍÍ
  1.016  DISP         ÿ Connect the UUT and the 1281 as follows:
  1.016  DISP         ÿ[27][91]1m     CHANNEL 1    TO        1281[27][91]m
  1.016  DISP         ÿ   OUTPUT (red)   ÄÄÄÄÄÄÄÄÄÄÄÄ> INPUT-HIGH
  1.016  DISP         ÿ   OUTPUT (black) ÄÄÄÄÄÄÄÄÄÄÄÄ> INPUT-LO
  1.017  CALL         Daytronic Excitation Sub
  1.018  HEAD         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
  1.019  HEAD         {º Excitation Voltage Test º}
  1.020  HEAD         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
  1.021  HEAD         {ÍÍ Channel 1 ÍÍ}
  1.022  HEAD         ÍÍ Excitation Voltage Test ÍÍ
  1.023  JMP          2.001
  1.024  EVAL
  2.001  DISP         ÿÿÿÿÿÿÿÿConnect the UUT as follows:
  2.001  DISP         + EXCITATION (pin 1) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16]1281 INPUT HI
  2.001  DISP         - EXCITATION (pin 4) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16]1281 INPUT LO
  2.002  CALL         Daytronic Excitation Sub
  2.003  HEAD         {}
  2.004  HEAD         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
  2.005  HEAD         {º Strain Indication Tests º}
  2.006  HEAD         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
  2.007  HEAD         {ÍÍ Channel 1 ÍÍ}
  2.008  HEAD         ÍÍ Channel 1 Strain Indication Tests ÍÍ
  2.009  JMP          3.001
  2.010  EVAL
  3.001  DISP         Set the 1550A 350ê bridge S+ shorting link to the closed
  3.001  DISP         position.
  3.002  DISP         ÿ   Connect the UUT channel 1 as follows:
  3.002  DISP         +SIGNAL (pin 2) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16]1550A +S
  3.002  DISP         -SIGNAL (pin 3) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16]1550A -S
  3.002  DISP         + EXCITATION (pin 1) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16]1550A +P
  3.002  DISP         - EXCITATION (pin 4) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄ[16]1550A -P
  3.003  PORT         RST[13]
  3.004  PORT         BIT999=1[13]
# 3.005  PORT         LCT 1=1011[13]
  3.005  PORT         LCT 1=11[13]
  3.006  PORT         RST 1[13]
  3.007  PORT         TYP 1=72[13]
  3.008  MATH         m[1]=1
  3.009  CALL         Daytronic Strain Indication Sub
  3.010  HEAD         {}
  3.011  HEAD         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
  3.012  HEAD         {º Excitation Voltage Test º}
  3.013  HEAD         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
  3.014  HEAD         {ÍÍ Channel 2 ÍÍ}
  3.015  HEAD         ÍÍ Excitation Voltage Test ÍÍ
  3.016  JMP          4.001
  3.017  EVAL
  4.001  DISP         Move the connector from Channel 1 to Channel 2.
  4.002  CALL         Daytronic Excitation Sub
  4.003  HEAD         {}
  4.004  HEAD         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
  4.005  HEAD         {º Strain Indication Tests º}
  4.006  HEAD         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
  4.007  HEAD         {ÍÍ Channel 2 ÍÍ}
  4.008  HEAD         ÍÍ Channel 2 Strain Indication Tests ÍÍ
  4.009  JMP          5.002
  4.010  EVAL
  5.001  PORT         BIT999=1[13]
# 5.002  PORT         LCT 2=1012[13]
  5.001  PORT         LCT 2=12[13]
  5.001  PORT         TYP 2=72[13]
  5.002  MATH         m[1]=2
  5.003  CALL         Daytronic Strain Indication Sub
  5.004  HEAD         {}
  5.005  DISP         {ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»}
  5.005  DISP         {º THIS COMPLETES THE VERIFICATION º}
  5.005  DISP         {ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ}
  5.006  END